AVION Travel Trailers

I have 3 round 12v interior floor lights. I'm try to figure out where they get their power. Maybe a switch tied to the front ceiling light?

Any ideas? Thanks.

That is a good question..... mine do not work, and I think I have tested the bulbs and verified that they will light up with 12VDC on them.

The "Indirect Lighting" switch makes the lights in the front above the open shelving come on.

(My "ceiling lights" switch doesn't make anything come on or off, either.)

silverloaf wrote: ↑Mon Oct 01, 2018 6:38 pm I have 3 round 12v interior floor lights. I'm try to figure out where they get their power. Maybe a switch tied to the front ceiling light?

Any ideas? Thanks.

Would you be able to share a photo of these floor lights? My Avion does not seem to have any (unless I've missed them). I am trying to understand what these lights are and look like. Thanks!

https://www.etrailer.com/Trailer-Lights ... L11CB.html


There are 2 additional ones on each side of the steps. I'm replacing them with the one above. They are wired into the porch light switch. You can barely see them in the pic below.

Funny, but they were each $0.86 cheaper when I ordered them last Saturday.

I hope you can see the round lights near the floor. One at the base of the dinette seat, one in the hallway below the drawers/doors, and one below the bathroom cabinet.

Same story here on the indirect floor lighting. Half moon mid 70's Chevy truck license plate lights.
As for the porch lights, I found LED lights in this style at Tractor Supply. Work great! Quite bright.

Thanks for the photos guys. Our 78 does not seem to have these floor lights. We do have a license plate light that is not working. I will order via the etrailer link silverloaf shared.

Salty wrote: ↑Tue Oct 02, 2018 1:22 am Same story here on the indirect floor lighting. Half moon mid 70's Chevy truck license plate lights.
As for the porch lights, I found LED lights in this style at Tractor Supply. Work great! Quite bright.

You mind sharing a pic of that porch light you got at TSC?

Razorback wrote: ↑Mon Oct 01, 2018 7:41 pm That is a good question..... mine do not work, and I think I have tested the bulbs and verified that they will light up with 12VDC on them.

The "Indirect Lighting" switch makes the lights in the front above the open shelving come on.

(My "ceiling lights" switch doesn't make anything come on or off, either.)

My new porch light wouldn't light up. I went to the 12v fuse panel and found the top 20A fuse had blown. I replaced it and it blew again. I pulled the 4-gang switch assy. out of its opening and did some circuit checks.

As I did my circuit check, I flipped each switch. I flipped the porch light, front trailer light and indirect lighting switches in sequence. All lit up. When I flipped the ceiling light switch, it blew the fuse.

I removed the ceiling light and found a set of wires from the switch and another set that disappeared above the ceiling. When I separated the wires, I had power to the light. When connected together, the fuse would blow.

I don't know the destination of the rogue wire. I began to think it was wired into the floor lights and got shorted out. Since the ceiling light has its own on-off switch, I thought maybe the ceiling light switch on the wall also controlled the floor lights.

By the way, I found 6-7 14-gauge white wires jammed into one too-small wire nut behind the wall switches. Some were loose. I installed a larger wire nut.

Anyway, I've now assigned a low priority to the floor lights. I'll get the ceiling light working and leave the roque wire disconnected for now.

I did some additional sleuthing to find the end point of the rogue wire mentioned above. I think found it connected to the floor light under the fridge.

In the attached pic are two sets of wires. Both were connected to the floor light. I separated the wires and ran a power supply to each. The bottom wire in the pic blew the fuse; the top wire did not. I'm confident the bottom wire runs to the ceiling light.

That being solved, my next challenge is to figure out where to fish a wire to the wall switch or install a new switch on the wood fridge cabinet. I have a hot wire under the fridge that originally went to the smoke/carbon monoxide detector.

What would you do?